DTC Code P1062 – What does this code mean?

Severity:
critical
<p><b>DTC Code P1062</b> indicates a Valvetronics Limp Home Request where the full stroke position is reached. This code is triggered when the Valvetronic system, which adjusts intake valve timing and duration, enters emergency operation mode due to the absence of a VVT sensor signal, causing the unit to reach its upper travel limit.</p>

Symptoms for Fault Code P1062

<ul> <li><a href="/problems/engine-warning-light-on"><b>Engine Light ON</b></a>: The engine light or service engine soon warning light illuminates, indicating a potential issue with the valvetronic system.</li> <li><a href="/problems/decreasing-engine-performance"><b>Reduced Engine Performance</b></a>: The vehicle may experience reduced engine performance due to the valvetronic system entering limp home mode.</li> <li><a href="/problems/rough-idle"><b>Rough Idling</b></a>: The engine may idle roughly as the valvetronic system is not operating optimally.</li> <li><a href="/problems/high-fuel-consumption"><b>Increased Fuel Consumption</b></a>: Fuel consumption may increase as the engine compensates for the valvetronic system's inability to adjust valve lift effectively.</li> </ul>

Common Causes for Fault Code P1062

<ul><li>The Valvetronic sensor may be malfunctioning, leading to incorrect readings and triggering the limp home mode.</li><li>An open or shorted harness in the Valvetronic sensor can disrupt the signal, causing the system to default to a safe mode.</li><li>Poor electrical connections in the Valvetronic sensor circuit can result in intermittent or failed communication with the control module.</li><li>Mechanical components within the Valvetronic system may be binding, preventing proper movement and causing the system to reach a full stroke position.</li></ul>

Determine the
root cause with AI

Enter symptoms and error codes and analyze them with artificial intelligence
Car details
Symptoms
Error codes
Thank you!
Oops! Something went wrong while submitting the form.
✓ Quick
Diagnosis in less than 3 min
✓ Free
No hidden fees
✓ Personalized
Tailored to your case
✓ Data-based
with >40k reference case

Troubleshooting for Fault Code P1062

<ul> <li><b>Initial Scan and Verification</b>: Use a diagnostic scanner to confirm the presence of DTC P1062. Clear the code and perform a test drive to see if it reappears.</li> <li><b>Inspect Valvetronic Motor</b>: Check the Valvetronic motor for any signs of damage or wear. Ensure the motor is functioning correctly and is not obstructed.</li> <li><b>Check Valvetronic Position Sensor</b>: Inspect the Valvetronic position sensor for proper operation. Verify the sensor's wiring and connections for any signs of damage or corrosion.</li> <li><b>Examine Wiring and Connectors</b>: Inspect the wiring harness and connectors related to the Valvetronic system. Look for any loose connections, frayed wires, or corrosion.</li> <li><b>Test Battery Voltage</b>: Ensure the vehicle's battery is providing adequate voltage. Low voltage can affect the Valvetronic system's performance.</li> <li><b>Perform Valvetronic System Calibration</b>: If all components are in good condition, perform a Valvetronic system calibration using the appropriate diagnostic tool.</li> <li><b>Re-evaluate and Test Drive</b>: After repairs and calibrations, clear the DTC and conduct a test drive to ensure the issue is resolved and the code does not return.</li></ul>

Severity Description for Fault Code P1062

<p>The DTC P1062 indicates a <b>critical</b> issue with the Valvetronics system, specifically a limp home request due to the full stroke position being reached. This can lead to <ul><li>significant engine performance issues</li><li>potential engine damage</li><li>reduced fuel efficiency</li></ul>. Immediate attention is required to prevent further complications and ensure vehicle safety.</p>

Related error codes

P0702

P0703

P0705

P0704

P1330

C111A

MechanX strives to provide correct information, but assumes no liability for any errors.
Please don't rely solely on our content.